Upgrade nilrt/master/5.10 to 5.10.115-rt67#64
Merged
gratian merged 1167 commits intoni:nilrt/master/5.10from May 24, 2022
Merged
Upgrade nilrt/master/5.10 to 5.10.115-rt67#64gratian merged 1167 commits intoni:nilrt/master/5.10from
gratian merged 1167 commits intoni:nilrt/master/5.10from
Conversation
[ Upstream commit 1a7eb80 ] Both of of_get_parent() and of_parse_phandle() return node pointer with refcount incremented, use of_node_put() on it to decrease refcount when done. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 047ae66 ] kzalloc() is a memory allocation function which can return NULL when some internal memory errors happen. So it is better to check it to prevent potential wrong memory access. Besides, since mdp5_plane_reset() is void type, so we should better set `plane-state` to NULL after releasing it. Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Patchwork: https://patchwork.freedesktop.org/patch/481055/ Link: https://lore.kernel.org/r/tencent_8E2A1C78140EE1784AB2FF4B2088CC0AB908@qq.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad7f18 ] commit 4298388 ("net: macb: restart tx after tx used bit read") added support for restarting transmission. Restarting tx does not work in case controller asserts TXUBR interrupt and TQBP is already at the end of the tx queue. In that situation, restarting tx will immediately cause assertion of another TXUBR interrupt. The driver will end up in an infinite interrupt loop which it cannot break out of. For cases where TQBP is at the end of the tx queue, instead only clear TX_USED interrupt. As more data gets pushed to the queue, transmission will resume. This issue was observed on a Xilinx Zynq-7000 based board. During stress test of the network interface, driver would get stuck on interrupt loop within seconds or minutes causing CPU to stall. Signed-off-by: Tomas Melin <tomas.melin@vaisala.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220407161659.14532-1-tomas.melin@vaisala.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 857b065 ] We set the qedi_ep state to EP_STATE_OFLDCONN_START when the ep is created. Then in qedi_set_path we kick off the offload work. If userspace times out the connection and calls ep_disconnect, qedi will only flush the offload work if the qedi_ep state has transitioned away from EP_STATE_OFLDCONN_START. If we can't connect we will not have transitioned state and will leave the offload work running, and we will free the qedi_ep from under it. This patch just has us init the work when we create the ep, then always flush it. Link: https://lore.kernel.org/r/20220408001314.5014-10-michael.christie@oracle.com Tested-by: Manish Rangankar <mrangankar@marvell.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Chris Leech <cleech@redhat.com> Acked-by: Manish Rangankar <mrangankar@marvell.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 932aba1 ] struct stat (defined in arch/x86/include/uapi/asm/stat.h) has 32-bit st_dev and st_rdev; struct compat_stat (defined in arch/x86/include/asm/compat.h) has 16-bit st_dev and st_rdev followed by a 16-bit padding. This patch fixes struct compat_stat to match struct stat. [ Historical note: the old x86 'struct stat' did have that 16-bit field that the compat layer had kept around, but it was changes back in 2003 by "struct stat - support larger dev_t": https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/?id=e95b2065677fe32512a597a79db94b77b90c968d and back in those days, the x86_64 port was still new, and separate from the i386 code, and had already picked up the old version with a 16-bit st_dev field ] Note that we can't change compat_dev_t because it is used by compat_loop_info. Also, if the st_dev and st_rdev values are 32-bit, we don't have to use old_valid_dev to test if the value fits into them. This fixes -EOVERFLOW on filesystems that are on NVMe because NVMe uses the major number 259. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Cc: Andreas Schwab <schwab@linux-m68k.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00ff400 ] Add a quirk to disable using and exporting namespace identifiers for controllers where they are broken beyond repair. The most directly visible problem with non-unique namespace identifiers is that they break the /dev/disk/by-id/ links, with the link for a supposedly unique identifier now pointing to one of multiple possible namespaces that share the same ID, and a somewhat random selection of which one actually shows up. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66dd346 ] Qemu unconditionally reports a UUID, which depending on the qemu version is either all-null (which is incorrect but harmless) or contains a single bit set for all controllers. In addition it can also optionally report a eui64 which needs to be manually set. Disable namespace identifiers for Qemu controlles entirely even if in some cases they could be set correctly through manual intervention. Reported-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e2932d1 upstream. Currently, the error count is read wrongly from the status register. Read the count from the proper error count register (ERRCNT). [ bp: Massage. ] Fixes: b500b4a ("EDAC, synopsys: Add ECC support for ZynqMP DDR controller") Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220414102813.4468-1-shubhrajyoti.datta@xilinx.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f24d5a upstream. This is a fix for commit f679505 ("mm: mmap: Allow for "high" userspace addresses") for hugetlb. This patch adds support for "high" userspace addresses that are optionally supported on the system and have to be requested via a hint mechanism ("high" addr parameter to mmap). Architectures such as powerpc and x86 achieve this by making changes to their architectural versions of hugetlb_get_unmapped_area() function. However, arm64 uses the generic version of that function. So take into account arch_get_mmap_base() and arch_get_mmap_end() in hugetlb_get_unmapped_area(). To allow that, move those two macros out of mm/mmap.c into include/linux/sched/mm.h If these macros are not defined in architectural code then they default to (TASK_SIZE) and (base) so should not introduce any behavioural changes to architectures that do not define them. For the time being, only ARM64 is affected by this change. Catalin (ARM64) said "We should have fixed hugetlb_get_unmapped_area() as well when we added support for 52-bit VA. The reason for commit f679505 was to prevent normal mmap() from returning addresses above 48-bit by default as some user-space had hard assumptions about this. It's a slight ABI change if you do this for hugetlb_get_unmapped_area() but I doubt anyone would notice. It's more likely that the current behaviour would cause issues, so I'd rather have them consistent. Basically when arm64 gained support for 52-bit addresses we did not want user-space calling mmap() to suddenly get such high addresses, otherwise we could have inadvertently broken some programs (similar behaviour to x86 here). Hence we added commit f679505. But we missed hugetlbfs which could still get such high mmap() addresses. So in theory that's a potential regression that should have bee addressed at the same time as commit f679505 (and before arm64 enabled 52-bit addresses)" Link: https://lkml.kernel.org/r/ab847b6edb197bffdfe189e70fb4ac76bfe79e0d.1650033747.git.christophe.leroy@csgroup.eu Fixes: f679505 ("mm: mmap: Allow for "high" userspace addresses") Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Steve Capper <steve.capper@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: <stable@vger.kernel.org> [5.0.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…x cleanup commit e4a3840 upstream. The pthread struct is allocated on PRIVATE|ANONYMOUS memory [1] which can be targeted by the oom reaper. This mapping is used to store the futex robust list head; the kernel does not keep a copy of the robust list and instead references a userspace address to maintain the robustness during a process death. A race can occur between exit_mm and the oom reaper that allows the oom reaper to free the memory of the futex robust list before the exit path has handled the futex death: CPU1 CPU2 -------------------------------------------------------------------- page_fault do_exit "signal" wake_oom_reaper oom_reaper oom_reap_task_mm (invalidates mm) exit_mm exit_mm_release futex_exit_release futex_cleanup exit_robust_list get_user (EFAULT- can't access memory) If the get_user EFAULT's, the kernel will be unable to recover the waiters on the robust_list, leaving userspace mutexes hung indefinitely. Delay the OOM reaper, allowing more time for the exit path to perform the futex cleanup. Reproducer: https://gitlab.com/jsavitz/oom_futex_reproducer Based on a patch by Michal Hocko. Link: https://elixir.bootlin.com/glibc/glibc-2.35/source/nptl/allocatestack.c#L370 [1] Link: https://lkml.kernel.org/r/20220414144042.677008-1-npache@redhat.com Fixes: 2129258 ("mm: oom: let oom_reap_task and exit_mmap run concurrently") Signed-off-by: Joel Savitz <jsavitz@redhat.com> Signed-off-by: Nico Pache <npache@redhat.com> Co-developed-by: Joel Savitz <jsavitz@redhat.com> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Rafael Aquini <aquini@redhat.com> Cc: Waiman Long <longman@redhat.com> Cc: Herton R. Krzesinski <herton@redhat.com> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ben Segall <bsegall@google.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Joel Savitz <jsavitz@redhat.com> Cc: Darren Hart <dvhart@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3195616 upstream. In some cases it is possible for mmu_interval_notifier_remove() to race with mn_tree_inv_end() allowing it to return while the notifier data structure is still in use. Consider the following sequence: CPU0 - mn_tree_inv_end() CPU1 - mmu_interval_notifier_remove() ----------------------------------- ------------------------------------ spin_lock(subscriptions->lock); seq = subscriptions->invalidate_seq; spin_lock(subscriptions->lock); spin_unlock(subscriptions->lock); subscriptions->invalidate_seq++; wait_event(invalidate_seq != seq); return; interval_tree_remove(interval_sub); kfree(interval_sub); spin_unlock(subscriptions->lock); wake_up_all(); As the wait_event() condition is true it will return immediately. This can lead to use-after-free type errors if the caller frees the data structure containing the interval notifier subscription while it is still on a deferred list. Fix this by taking the appropriate lock when reading invalidate_seq to ensure proper synchronisation. I observed this whilst running stress testing during some development. You do have to be pretty unlucky, but it leads to the usual problems of use-after-free (memory corruption, kernel crash, difficult to diagnose WARN_ON, etc). Link: https://lkml.kernel.org/r/20220420043734.476348-1-apopple@nvidia.com Fixes: 99cb252 ("mm/mmu_notifier: add an interval tree notifier") Signed-off-by: Alistair Popple <apopple@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Cc: Christian König <christian.koenig@amd.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aafa9f9 upstream. Before detecting the cable type on the dma bar, the driver should check whether the 'bmdma_addr' is zero, which means the adapter does not support DMA, otherwise we will get the following error: [ 5.146634] Bad IO access at port 0x1 (return inb(port)) [ 5.147206] WARNING: CPU: 2 PID: 303 at lib/iomap.c:44 ioread8+0x4a/0x60 [ 5.150856] RIP: 0010:ioread8+0x4a/0x60 [ 5.160238] Call Trace: [ 5.160470] <TASK> [ 5.160674] marvell_cable_detect+0x6e/0xc0 [pata_marvell] [ 5.161728] ata_eh_recover+0x3520/0x6cc0 [ 5.168075] ata_do_eh+0x49/0x3c0 Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 206680c upstream. The bug is here: __func__, desc, &desc->tx_dma_desc.phys, ret, cookie, residue); The list iterator 'desc' will point to a bogus position containing HEAD if the list is empty or no element is found. To avoid dev_dbg() prints a invalid address, use a new variable 'iter' as the list iterator, while use the origin variable 'desc' as a dedicated pointer to point to the found element. Cc: stable@vger.kernel.org Fixes: 82e2424 ("dmaengine: xdmac: fix print warning on dma_addr_t variable") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Link: https://lore.kernel.org/r/20220327061154.4867-1-xiam0nd.tong@gmail.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbe6c3a upstream. This will reset deeply on freeze and thaw instead of suspend and resume and prevent null pointer dereferences of the uninitialized ring 0 buffer while thawing. The impact is an indefinitely hanging kernel. You can't switch consoles after this and the only possible user interaction is SysRq. BUG: kernel NULL pointer dereference RIP: 0010:aq_ring_rx_fill+0xcf/0x210 [atlantic] aq_vec_init+0x85/0xe0 [atlantic] aq_nic_init+0xf7/0x1d0 [atlantic] atl_resume_common+0x4f/0x100 [atlantic] pci_pm_thaw+0x42/0xa0 resolves in aq_ring.o to ``` 0000000000000ae0 <aq_ring_rx_fill>: { /* ... */ baf: 48 8b 43 08 mov 0x8(%rbx),%rax buff->flags = 0U; /* buff is NULL */ ``` The bug has been present since the introduction of the new pm code in 8aaa112 ("net: atlantic: refactoring pm logic") and was hidden until 8ce8427 ("net: atlantic: changes for multi-TC support"), which refactored the aq_vec_{free,alloc} functions into aq_vec_{,ring}_{free,alloc}, but is technically not wrong. The original functions just always reinitialized the buffers on S3/S4. If the interface is down before freezing, the bug does not occur. It does not matter, whether the initrd contains and loads the module before thawing. So the fix is to invert the boolean parameter deep in all pm function calls, which was clearly intended to be set like that. First report was on Github [1], which you have to guess from the resume logs in the posted dmesg snippet. Recently I posted one on Bugzilla [2], since I did not have an AQC device so far. #regzbot introduced: 8ce8427 #regzbot from: koo5 <kolman.jindrich@gmail.com> #regzbot monitor: Aquantia/AQtion#32 Fixes: 8aaa112 ("net: atlantic: refactoring pm logic") Link: Aquantia/AQtion#32 [1] Link: https://bugzilla.kernel.org/show_bug.cgi?id=215798 [2] Cc: stable@vger.kernel.org Reported-by: koo5 <kolman.jindrich@gmail.com> Signed-off-by: Manuel Ullmann <labre@posteo.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee69d4b upstream. These patch_text implementations are using stop_machine_cpuslocked infrastructure with atomic cpu_count. The original idea: When the master CPU patch_text, the others should wait for it. But current implementation is using the first CPU as master, which couldn't guarantee the remaining CPUs are waiting. This patch changes the last CPU as the master to solve the potential risk. Fixes: 64711f9 ("xtensa: implement jump_label support") Signed-off-by: Guo Ren <guoren@linux.alibaba.com> Signed-off-by: Guo Ren <guoren@kernel.org> Reviewed-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: <stable@vger.kernel.org> Message-Id: <20220407073323.743224-4-guoren@kernel.org> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 839769c upstream. Fast coprocessor exception handler saves a3..a6, but coprocessor context load/store code uses a4..a7 as temporaries, potentially clobbering a7. 'Potentially' because coprocessor state load/store macros may not use all four temporary registers (and neither FPU nor HiFi macros do). Use a3..a6 as intended. Cc: stable@vger.kernel.org Fixes: c658eac ("[XTENSA] Add support for configurable registers and coprocessors") Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefa91b upstream. Given a sufficiently large number of actions, while copying and reserving memory for a new action of a new flow, if next_offset is greater than MAX_ACTIONS_BUFSIZE, the function reserve_sfa_size() does not return -EMSGSIZE as expected, but it allocates MAX_ACTIONS_BUFSIZE bytes increasing actions_len by req_size. This can then lead to an OOB write access, especially when further actions need to be copied. Fix it by rearranging the flow action size check. KASAN splat below: ================================================================== BUG: KASAN: slab-out-of-bounds in reserve_sfa_size+0x1ba/0x380 [openvswitch] Write of size 65360 at addr ffff888147e4001c by task handler15/836 CPU: 1 PID: 836 Comm: handler15 Not tainted 5.18.0-rc1+ ni#27 ... Call Trace: <TASK> dump_stack_lvl+0x45/0x5a print_report.cold+0x5e/0x5db ? __lock_text_start+0x8/0x8 ? reserve_sfa_size+0x1ba/0x380 [openvswitch] kasan_report+0xb5/0x130 ? reserve_sfa_size+0x1ba/0x380 [openvswitch] kasan_check_range+0xf5/0x1d0 memcpy+0x39/0x60 reserve_sfa_size+0x1ba/0x380 [openvswitch] __add_action+0x24/0x120 [openvswitch] ovs_nla_add_action+0xe/0x20 [openvswitch] ovs_ct_copy_action+0x29d/0x1130 [openvswitch] ? __kernel_text_address+0xe/0x30 ? unwind_get_return_address+0x56/0xa0 ? create_prof_cpu_mask+0x20/0x20 ? ovs_ct_verify+0xf0/0xf0 [openvswitch] ? prep_compound_page+0x198/0x2a0 ? __kasan_check_byte+0x10/0x40 ? kasan_unpoison+0x40/0x70 ? ksize+0x44/0x60 ? reserve_sfa_size+0x75/0x380 [openvswitch] __ovs_nla_copy_actions+0xc26/0x2070 [openvswitch] ? __zone_watermark_ok+0x420/0x420 ? validate_set.constprop.0+0xc90/0xc90 [openvswitch] ? __alloc_pages+0x1a9/0x3e0 ? __alloc_pages_slowpath.constprop.0+0x1da0/0x1da0 ? unwind_next_frame+0x991/0x1e40 ? __mod_node_page_state+0x99/0x120 ? __mod_lruvec_page_state+0x2e3/0x470 ? __kasan_kmalloc_large+0x90/0xe0 ovs_nla_copy_actions+0x1b4/0x2c0 [openvswitch] ovs_flow_cmd_new+0x3cd/0xb10 [openvswitch] ... Cc: stable@vger.kernel.org Fixes: f28cd2a ("openvswitch: fix flow actions reallocation") Signed-off-by: Paolo Valerio <pvalerio@redhat.com> Acked-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06fb4ec upstream. Commit 5467801 ("gpio: Restrict usage of GPIO chip irq members before initialization") attempted to fix a race condition that lead to a NULL pointer, but in the process caused a regression for _AEI/_EVT declared GPIOs. This manifests in messages showing deferred probing while trying to allocate IRQs like so: amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x0000 to IRQ, err -517 amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x002C to IRQ, err -517 amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x003D to IRQ, err -517 [ .. more of the same .. ] The code for walking _AEI doesn't handle deferred probing and so this leads to non-functional GPIO interrupts. Fix this issue by moving the call to `acpi_gpiochip_request_interrupts` to occur after gc->irc.initialized is set. Fixes: 5467801 ("gpio: Restrict usage of GPIO chip irq members before initialization") Link: https://lore.kernel.org/linux-gpio/BL1PR12MB51577A77F000A008AA694675E2EF9@BL1PR12MB5157.namprd12.prod.outlook.com/ Link: https://bugzilla.suse.com/show_bug.cgi?id=1198697 Link: https://bugzilla.kernel.org/show_bug.cgi?id=215850 Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1979 Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1976 Reported-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Shreeya Patel <shreeya.patel@collabora.com> Tested-By: Samuel Čavoj <samuel@cavoj.net> Tested-By: lukeluk498@gmail.com Link: Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-and-tested-by: Takashi Iwai <tiwai@suse.de> Cc: Shreeya Patel <shreeya.patel@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f730a46 upstream. These two bug are here: list_for_each_entry_safe_continue(w, n, list, power_list); list_for_each_entry_safe_continue(w, n, list, power_list); After the list_for_each_entry_safe_continue() exits, the list iterator will always be a bogus pointer which point to an invalid struct objdect containing HEAD member. The funciton poniter 'w->event' will be a invalid value which can lead to a control-flow hijack if the 'w' can be controlled. The original intention was to continue the outer list_for_each_entry_safe() loop with the same entry if w->event is NULL, but misunderstanding the meaning of list_for_each_entry_safe_continue(). So just add a 'continue;' to fix the bug. Cc: stable@vger.kernel.org Fixes: 163cac0 ("ASoC: Factor out DAPM sequence execution") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Link: https://lore.kernel.org/r/20220329012134.9375-1-xiam0nd.tong@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04ebaa1 upstream. When we decode the latency and the max_latency, u16 value may not fit the required size and could lead to the wrong LTR representation. Scaling is represented as: scale 0 - 1 (2^(5*0)) = 2^0 scale 1 - 32 (2^(5 *1))= 2^5 scale 2 - 1024 (2^(5 *2)) =2^10 scale 3 - 32768 (2^(5 *3)) =2^15 scale 4 - 1048576 (2^(5 *4)) = 2^20 scale 5 - 33554432 (2^(5 *4)) = 2^25 scale 4 and scale 5 required 20 and 25 bits respectively. scale 6 reserved. Replace the u16 type with the u32 type and allow corrected LTR representation. Cc: stable@vger.kernel.org Fixes: 44a13a5 ("e1000e: Fix the max snoop/no-snoop latency for 10M") Reported-by: James Hutchinson <jahutchinson99@googlemail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215689 Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Tested-by: James Hutchinson <jahutchinson99@googlemail.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1c6ecf upstream. Function syscall_trace_exit expects pointer to pt_regs. However r0 is also used to keep syscall return value. Restore pointer to pt_regs before calling syscall_trace_exit. Cc: <stable@vger.kernel.org> Signed-off-by: Sergey Matyukevich <sergey.matyukevich@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5c2377 upstream. In the case where there is only a cycle counter available (i.e. PMCR_EL0.N is 0) and an event other than CPU cycles is opened, the open should fail as the event can never possibly be scheduled. However, the event validation when an event is opened is skipped when the group leader is opened. Fix this by always validating the group leader events. Reported-by: Al Grant <al.grant@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/r/20220408203330.4014015-1-robh@kernel.org Cc: <stable@vger.kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 40f5aa4 ] The warning in cfs_rq_is_decayed() triggered: SCHED_WARN_ON(cfs_rq->avg.load_avg || cfs_rq->avg.util_avg || cfs_rq->avg.runnable_avg) There exists a corner case in attach_entity_load_avg() which will cause load_sum to be zero while load_avg will not be. Consider se_weight is 88761 as per the sched_prio_to_weight[] table. Further assume the get_pelt_divider() is 47742, this gives: se->avg.load_avg is 1. However, calculating load_sum: se->avg.load_sum = div_u64(se->avg.load_avg * se->avg.load_sum, se_weight(se)); se->avg.load_sum = 1*47742/88761 = 0. Then enqueue_load_avg() adds this to the cfs_rq totals: cfs_rq->avg.load_avg += se->avg.load_avg; cfs_rq->avg.load_sum += se_weight(se) * se->avg.load_sum; Resulting in load_avg being 1 with load_sum is 0, which will trigger the WARN. Fixes: f207934 ("sched/fair: Align PELT windows between cfs_rq and its se") Signed-off-by: kuyo chang <kuyo.chang@mediatek.com> [peterz: massage changelog] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Link: https://lkml.kernel.org/r/20220414090229.342-1-kuyo.chang@mediatek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60490e7 ] This problem can be reproduced with CONFIG_PERF_USE_VMALLOC enabled on both x86_64 and aarch64 arch when using sysdig -B(using ebpf)[1]. sysdig -B works fine after rebuilding the kernel with CONFIG_PERF_USE_VMALLOC disabled. I tracked it down to the if condition event->rb->nr_pages != nr_pages in perf_mmap is true when CONFIG_PERF_USE_VMALLOC is enabled where event->rb->nr_pages = 1 and nr_pages = 2048 resulting perf_mmap to return -EINVAL. This is because when CONFIG_PERF_USE_VMALLOC is enabled, rb->nr_pages is always equal to 1. Arch with CONFIG_PERF_USE_VMALLOC enabled by default: arc/arm/csky/mips/sh/sparc/xtensa Arch with CONFIG_PERF_USE_VMALLOC disabled by default: x86_64/aarch64/... Fix this problem by using data_page_nr() [1] https://github.com/draios/sysdig Fixes: 906010b ("perf_event: Provide vmalloc() based mmap() backing") Signed-off-by: Zhipeng Xie <xiezhipeng1@huawei.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20220209145417.6495-1-xiezhipeng1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f92055a ] If a call to rpi_touchscreen_i2c_write from rpi_touchscreen_probe fails before mipi_dsi_device_register_full is called, then in trying to log the error message if uses ts->dsi->dev when it is still NULL. Use ts->i2c->dev instead, which is initialised earlier in probe. Fixes: 2f733d6 ("drm/panel: Add support for the Raspberry Pi 7" Touchscreen.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220415162513.42190-2-stefan.wahren@i2se.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f18c07 ] The panel has a prepare call which is before video starts, and an enable call which is after. The Toshiba bridge should be configured before video, so move the relevant power and initialisation calls to prepare. Fixes: 2f733d6 ("drm/panel: Add support for the Raspberry Pi 7" Touchscreen.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220415162513.42190-3-stefan.wahren@i2se.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26a62b7 ] The LoPAPR spec defines a guest visible IOMMU with a variable page size. Currently QEMU advertises 4K, 64K, 2M, 16MB pages, a Linux VM picks the biggest (16MB). In the case of a passed though PCI device, there is a hardware IOMMU which does not support all pages sizes from the above - P8 cannot do 2MB and P9 cannot do 16MB. So for each emulated 16M IOMMU page we may create several smaller mappings ("TCEs") in the hardware IOMMU. The code wrongly uses the emulated TCE index instead of hardware TCE index in error handling. The problem is easier to see on POWER8 with multi-level TCE tables (when only the first level is preallocated) as hash mode uses real mode TCE hypercalls handlers. The kernel starts using indirect tables when VMs get bigger than 128GB (depends on the max page order). The very first real mode hcall is going to fail with H_TOO_HARD as in the real mode we cannot allocate memory for TCEs (we can in the virtual mode) but on the way out the code attempts to clear hardware TCEs using emulated TCE indexes which corrupts random kernel memory because it_offset==1<<59 is subtracted from those indexes and the resulting index is out of the TCE table bounds. This fixes kvmppc_clear_tce() to use the correct TCE indexes. While at it, this fixes TCE cache invalidation which uses emulated TCE indexes instead of the hardware ones. This went unnoticed as 64bit DMA is used these days and VMs map all RAM in one go and only then do DMA and this is when the TCE cache gets populated. Potentially this could slow down mapping, however normally 16MB emulated pages are backed by 64K hardware pages so it is one write to the "TCE Kill" per 256 updates which is not that bad considering the size of the cache (1024 TCEs or so). Fixes: ca1fc48 ("KVM: PPC: Book3S: Allow backing bigger guest IOMMU pages with smaller physical pages") Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Tested-by: David Gibson <david@gibson.dropbear.id.au> Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com> Reviewed-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220420050840.328223-1-aik@ozlabs.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
…sage [ Upstream commit 3d0b93d ] If the device is already in a runtime PM enabled state pm_runtime_get_sync() will return 1. Also, we need to call pm_runtime_put_noidle() when pm_runtime_get_sync() fails, so use pm_runtime_resume_and_get() instead. this function will handle this. Fixes: 4078f57 ("drm/vc4: Add DSI driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220420135008.2757-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dcad70 ] When scheduling a group of events, there are constraint checks done to make sure all events can go in a group. Example, one of the criteria is that events in a group cannot use the same PMC. But platform specific PMU supports alternative event for some of the event codes. During perf_event_open(), if any event group doesn't match constraint check criteria, further lookup is done to find alternative event. By current design, the array of alternatives events in PMU code is expected to be sorted by column 0. This is because in find_alternative() the return criteria is based on event code comparison. ie. "event < ev_alt[i][0])". This optimisation is there since find_alternative() can be called multiple times. In power9 PMU code, the alternative event array is not sorted properly and hence there is breakage in finding alternative events. To work with existing logic, fix the alternative event array to be sorted by column 0 for power9-pmu.c Results: With alternative events, multiplexing can be avoided. That is, for example, in power9 PM_LD_MISS_L1 (0x3e054) has alternative event, PM_LD_MISS_L1_ALT (0x400f0). This is an identical event which can be programmed in a different PMC. Before: # perf stat -e r3e054,r300fc Performance counter stats for 'system wide': 1057860 r3e054 (50.21%) 379 r300fc (49.79%) 0.944329741 seconds time elapsed Since both the events are using PMC3 in this case, they are multiplexed here. After: # perf stat -e r3e054,r300fc Performance counter stats for 'system wide': 1006948 r3e054 182 r300fc Fixes: 91e0bd1 ("powerpc/perf: Add PM_LD_MISS_L1 and PM_BR_2PATH to power9 event list") Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com> Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220419114828.89843-1-atrajeev@linux.vnet.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ccb17ca ] Since commit bb30aca ("perf report: Bail out --mem-mode if mem info is not available") "perf mem report" and "perf report --mem-mode" don't report result if the PERF_SAMPLE_DATA_SRC bit is missed in sample type. The commit ffab487 ("perf: arm-spe: Fix perf report --mem-mode") partially fixes the issue. It adds PERF_SAMPLE_DATA_SRC bit for Arm SPE event, this allows the perf data file generated by kernel v5.18-rc1 or later version can be reported properly. On the other hand, perf tool still fails to be backward compatibility for a data file recorded by an older version's perf which contains Arm SPE trace data. This patch is a workaround in reporting phase, when detects ARM SPE PMU event and without PERF_SAMPLE_DATA_SRC bit, it will force to set the bit in the sample type and give a warning info. Fixes: bb30aca ("perf report: Bail out --mem-mode if mem info is not available") Reviewed-by: James Clark <james.clark@arm.com> Signed-off-by: Leo Yan <leo.yan@linaro.org> Tested-by: German Gomez <german.gomez@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Link: https://lore.kernel.org/r/20220414123201.842754-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
… PMU [ Upstream commit 5a1bde4 ] On some x86 processors, CPUID leaf 0xA provides information on Architectural Performance Monitoring features. It advertises a PMU version which Qemu uses to determine the availability of additional MSRs to manage the PMCs. Upon receiving a KVM_GET_SUPPORTED_CPUID ioctl request for the same, the kernel constructs return values based on the x86_pmu_capability irrespective of the vendor. This leaf and the additional MSRs are not supported on AMD and Hygon processors. If AMD PerfMonV2 is detected, the PMU version is set to 2 and guest startup breaks because of an attempt to access a non-existent MSR. Return zeros to avoid this. Fixes: a6c06ed ("KVM: Expose the architectural performance monitoring CPUID leaf") Reported-by: Vasant Hegde <vasant.hegde@amd.com> Signed-off-by: Sandipan Das <sandipan.das@amd.com> Message-Id: <3fef83d9c2b2f7516e8ff50d60851f29a4bcb716.1651058600.git.sandipan.das@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ba2d9d ] Resource dump menu may span over more than a single page, support it. Otherwise, menu read may result in a memory access violation: reading outside of the allocated page. Note that page format of the first menu page contains menu headers while the proceeding menu pages contain only records. The KASAN logs are as follows: BUG: KASAN: slab-out-of-bounds in strcmp+0x9b/0xb0 Read of size 1 at addr ffff88812b2e1fd0 by task systemd-udevd/496 CPU: 5 PID: 496 Comm: systemd-udevd Tainted: G B 5.16.0_for_upstream_debug_2022_01_10_23_12 #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x57/0x7d print_address_description.constprop.0+0x1f/0x140 ? strcmp+0x9b/0xb0 ? strcmp+0x9b/0xb0 kasan_report.cold+0x83/0xdf ? strcmp+0x9b/0xb0 strcmp+0x9b/0xb0 mlx5_rsc_dump_init+0x4ab/0x780 [mlx5_core] ? mlx5_rsc_dump_destroy+0x80/0x80 [mlx5_core] ? lockdep_hardirqs_on_prepare+0x286/0x400 ? raw_spin_unlock_irqrestore+0x47/0x50 ? aomic_notifier_chain_register+0x32/0x40 mlx5_load+0x104/0x2e0 [mlx5_core] mlx5_init_one+0x41b/0x610 [mlx5_core] .... The buggy address belongs to the object at ffff88812b2e0000 which belongs to the cache kmalloc-4k of size 4096 The buggy address is located 4048 bytes to the right of 4096-byte region [ffff88812b2e0000, ffff88812b2e1000) The buggy address belongs to the page: page:000000009d69807a refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88812b2e6000 pfn:0x12b2e0 head:000000009d69807a order:3 compound_mapcount:0 compound_pincount:0 flags: 0x8000000000010200(slab|head|zone=2) raw: 8000000000010200 0000000000000000 dead000000000001 ffff888100043040 raw: ffff88812b2e6000 0000000080040000 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88812b2e1e80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88812b2e1f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff88812b2e1f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff88812b2e2000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88812b2e2080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== Fixes: 12206b1 ("net/mlx5: Add support for resource dump") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0361bdf ] MSR_KVM_POLL_CONTROL is cleared on reset, thus reverting guests to host-side polling after suspend/resume. Non-bootstrap CPUs are restored correctly by the haltpoll driver because they are hot-unplugged during suspend and hot-plugged during resume; however, the BSP is not hotpluggable and remains in host-sde polling mode after the guest resume. The makes the guest pay for the cost of vmexits every time the guest enters idle. Fix it by recording BSP's haltpoll state and resuming it during guest resume. Cc: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Message-Id: <1650267752-46796-1-git-send-email-wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d22a81b ] Emulating writes to SELF_IPI with a write to ICR has an unwanted side effect: the value of ICR in vAPIC page gets changed. The lists SELF_IPI as write-only, with no associated MMIO offset, so any write should have no visible side effect in the vAPIC page. Reported-by: Chao Gao <chao.gao@intel.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9191b8f ] WARN and bail if KVM attempts to free a root that isn't backed by a shadow page. KVM allocates a bare page for "special" roots, e.g. when using PAE paging or shadowing 2/3/4-level page tables with 4/5-level, and so root_hpa will be valid but won't be backed by a shadow page. It's all too easy to blindly call mmu_free_root_page() on root_hpa, be nice and WARN instead of crashing KVM and possibly the kernel. Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
…rtised [ Upstream commit 1714a4e ] As commit 0c5f81d ("KVM: LAPIC: Inject timer interrupt via posted interrupt") mentioned that the host admin should well tune the guest setup, so that vCPUs are placed on isolated pCPUs, and with several pCPUs surplus for *busy* housekeeping. In this setup, it is preferrable to disable mwait/hlt/pause vmexits to keep the vCPUs in non-root mode. However, if only some guests isolated and others not, they would not have any benefit from posted timer interrupts, and at the same time lose VMX preemption timer fast paths because kvm_can_post_timer_interrupt() returns true and therefore forces kvm_can_use_hv_timer() to false. By guaranteeing that posted-interrupt timer is only used if MWAIT or HLT are done without vmexit, KVM can make a better choice and use the VMX preemption timer and the corresponding fast paths. Reported-by: Aili Yao <yaoaili@kingsoft.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Cc: Aili Yao <yaoaili@kingsoft.com> Cc: Sean Christopherson <seanjc@google.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Message-Id: <1643112538-36743-1-git-send-email-wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e61e95 upstream. The callbacks processing time limit makes sure we are not exceeding a given amount of time executing the queue. However its "continue" clause bypasses the cond_resched() call on rcuc and NOCB kthreads, delaying it until we reach the limit, which can be very long... Make sure the scheduler has a higher priority than the time limit. Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Tested-by: Valentin Schneider <valentin.schneider@arm.com> Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Valentin Schneider <valentin.schneider@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Neeraj Upadhyay <neeraju@codeaurora.org> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> [UR: backport to 5.10-stable + commit update] Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a554ba2 upstream. Time limit only makes sense when callbacks are serviced in softirq mode because: _ In case we need to get back to the scheduler, cond_resched_tasks_rcu_qs() is called after each callback. _ In case some other softirq vector needs the CPU, the call to local_bh_enable() before cond_resched_tasks_rcu_qs() takes care about them via a call to do_softirq(). Therefore, make sure the time limit only applies to softirq mode. Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Tested-by: Valentin Schneider <valentin.schneider@arm.com> Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Valentin Schneider <valentin.schneider@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Neeraj Upadhyay <neeraju@codeaurora.org> Cc: Uladzislau Rezki <urezki@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> [UR: backport to 5.10-stable] Signed-off-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc8f7fe upstream. Add __GFP_ZERO flag for alloc_page in function bio_copy_kern to initialize the buffer of a bio. Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220216084038.15635-1-tcs.kernel@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk> [nobelbarakat: Backported to 5.10: Manually added flag] Signed-off-by: Nobel Barakat <nobelbarakat@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f6dc63 upstream. Commit d208b89 ("dm: fix mempool NULL pointer race when completing IO") didn't go far enough. When bio_end_io_acct ends the count of in-flight I/Os may reach zero and the DM device may be suspended. There is a possibility that the suspend races with dm_stats_account_io. Fix this by adding percpu "pending_io" counters to track outstanding dm_io. Move kicking of suspend queue to dm_io_dec_pending(). Also, rename md_in_flight_bios() to dm_in_flight_bios() and update it to iterate all pending_io counters. Fixes: d208b89 ("dm: fix mempool NULL pointer race when completing IO") Cc: stable@vger.kernel.org Co-developed-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7d8dc1f upstream. We already clear all the other interrupts (ISR0, ISR1, HOST_CTRL_INT). Define a new macro PCIE_MSI_ALL_MASK and do the same clearing for MSIs, to ensure that we don't start receiving spurious interrupts. Use this new mask in advk_pcie_handle_msi(); Link: https://lore.kernel.org/r/20211130172913.9727-5-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 805dfc1 upstream. In advk_pcie_handle_msi() it is expected that when bit i in the W1C register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is updated to contain the MSI number corresponding to index i. Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG always contains the number of the last received MSI, overall. Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt number. Since Aardvark already forbids more than 32 interrupts and uses own allocated hwirq numbers, the msi_idx already corresponds to the received MSI number. Link: https://lore.kernel.org/r/20220110015018.26359-3-kabel@kernel.org Fixes: 8c39d71 ("PCI: aardvark: Add Aardvark PCI host controller driver") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f311c9 upstream. SD spec definition: "Host provides at least 74 Clocks before issuing first command" After 1ms for the voltage stable then start issuing the Clock signals if POWER STATE is MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card Signed-off-by: Ricky Wu <ricky_wu@realtek.com> Link: https://lore.kernel.org/r/1badf10aba764191a1a752edcbf90389@realtek.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Christian Loehle <cloehle@hyperstone.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220510130732.861729621@linuxfoundation.org Tested-by: Pavel Machek (CIP) <pavel@denx.de> Tested-by: Fox Chen <foxhlchen@gmail.com> Tested-by: Shuah Khan <skhan@linuxfoundation.org> Tested-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Hulk Robot <hulkrobot@huawei.com> Tested-by: Linux Kernel Functional Testing <lkft@linaro.org> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Tested-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts: net/ipv4/inet_hashtables.c Signed-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Signed-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Conflicts: kernel/irq/manage.c kernel/trace/trace_events_trigger.c Signed-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Signed-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
amstewart
approved these changes
May 19, 2022
bstreiff
approved these changes
May 23, 2022
gratian
pushed a commit
that referenced
this pull request
Aug 29, 2024
commit 9a2fa14 upstream. copy_fd_bitmaps(new, old, count) is expected to copy the first count/BITS_PER_LONG bits from old->full_fds_bits[] and fill the rest with zeroes. What it does is copying enough words (BITS_TO_LONGS(count/BITS_PER_LONG)), then memsets the rest. That works fine, *if* all bits past the cutoff point are clear. Otherwise we are risking garbage from the last word we'd copied. For most of the callers that is true - expand_fdtable() has count equal to old->max_fds, so there's no open descriptors past count, let alone fully occupied words in ->open_fds[], which is what bits in ->full_fds_bits[] correspond to. The other caller (dup_fd()) passes sane_fdtable_size(old_fdt, max_fds), which is the smallest multiple of BITS_PER_LONG that covers all opened descriptors below max_fds. In the common case (copying on fork()) max_fds is ~0U, so all opened descriptors will be below it and we are fine, by the same reasons why the call in expand_fdtable() is safe. Unfortunately, there is a case where max_fds is less than that and where we might, indeed, end up with junk in ->full_fds_bits[] - close_range(from, to, CLOSE_RANGE_UNSHARE) with * descriptor table being currently shared * 'to' being above the current capacity of descriptor table * 'from' being just under some chunk of opened descriptors. In that case we end up with observably wrong behaviour - e.g. spawn a child with CLONE_FILES, get all descriptors in range 0..127 open, then close_range(64, ~0U, CLOSE_RANGE_UNSHARE) and watch dup(0) ending up with descriptor #128, despite #64 being observably not open. The minimally invasive fix would be to deal with that in dup_fd(). If this proves to add measurable overhead, we can go that way, but let's try to fix copy_fd_bitmaps() first. * new helper: bitmap_copy_and_expand(to, from, bits_to_copy, size). * make copy_fd_bitmaps() take the bitmap size in words, rather than bits; it's 'count' argument is always a multiple of BITS_PER_LONG, so we are not losing any information, and that way we can use the same helper for all three bitmaps - compiler will see that count is a multiple of BITS_PER_LONG for the large ones, so it'll generate plain memcpy()+memset(). Reproducer added to tools/testing/selftests/core/close_range_test.c Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gratian
pushed a commit
that referenced
this pull request
Sep 11, 2024
commit 9a2fa14 upstream. copy_fd_bitmaps(new, old, count) is expected to copy the first count/BITS_PER_LONG bits from old->full_fds_bits[] and fill the rest with zeroes. What it does is copying enough words (BITS_TO_LONGS(count/BITS_PER_LONG)), then memsets the rest. That works fine, *if* all bits past the cutoff point are clear. Otherwise we are risking garbage from the last word we'd copied. For most of the callers that is true - expand_fdtable() has count equal to old->max_fds, so there's no open descriptors past count, let alone fully occupied words in ->open_fds[], which is what bits in ->full_fds_bits[] correspond to. The other caller (dup_fd()) passes sane_fdtable_size(old_fdt, max_fds), which is the smallest multiple of BITS_PER_LONG that covers all opened descriptors below max_fds. In the common case (copying on fork()) max_fds is ~0U, so all opened descriptors will be below it and we are fine, by the same reasons why the call in expand_fdtable() is safe. Unfortunately, there is a case where max_fds is less than that and where we might, indeed, end up with junk in ->full_fds_bits[] - close_range(from, to, CLOSE_RANGE_UNSHARE) with * descriptor table being currently shared * 'to' being above the current capacity of descriptor table * 'from' being just under some chunk of opened descriptors. In that case we end up with observably wrong behaviour - e.g. spawn a child with CLONE_FILES, get all descriptors in range 0..127 open, then close_range(64, ~0U, CLOSE_RANGE_UNSHARE) and watch dup(0) ending up with descriptor #128, despite #64 being observably not open. The minimally invasive fix would be to deal with that in dup_fd(). If this proves to add measurable overhead, we can go that way, but let's try to fix copy_fd_bitmaps() first. * new helper: bitmap_copy_and_expand(to, from, bits_to_copy, size). * make copy_fd_bitmaps() take the bitmap size in words, rather than bits; it's 'count' argument is always a multiple of BITS_PER_LONG, so we are not losing any information, and that way we can use the same helper for all three bitmaps - compiler will see that count is a multiple of BITS_PER_LONG for the large ones, so it'll generate plain memcpy()+memset(). Reproducer added to tools/testing/selftests/core/close_range_test.c Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gratian
pushed a commit
that referenced
this pull request
Dec 6, 2024
[ Upstream commit 60f07e2 ] We use uprobe in aarch64_be, which we found the tracee task would exit due to SIGILL when we enable the uprobe trace. We can see the replace inst from uprobe is not correct in aarch big-endian. As in Armv8-A, instruction fetches are always treated as little-endian, we should treat the UPROBE_SWBP_INSN as little-endian。 The test case is as following。 bash-4.4# ./mqueue_test_aarchbe 1 1 2 1 10 > /dev/null & bash-4.4# cd /sys/kernel/debug/tracing/ bash-4.4# echo 'p:test /mqueue_test_aarchbe:0xc30 %x0 %x1' > uprobe_events bash-4.4# echo 1 > events/uprobes/enable bash-4.4# bash-4.4# ps PID TTY TIME CMD 140 ? 00:00:01 bash 237 ? 00:00:00 ps [1]+ Illegal instruction ./mqueue_test_aarchbe 1 1 2 1 100 > /dev/null which we debug use gdb as following: bash-4.4# gdb attach 155 (gdb) disassemble send Dump of assembler code for function send: 0x0000000000400c30 <+0>: .inst 0xa00020d4 ; undefined 0x0000000000400c34 <+4>: mov x29, sp 0x0000000000400c38 <+8>: str w0, [sp, #28] 0x0000000000400c3c <+12>: strb w1, [sp, #27] 0x0000000000400c40 <+16>: str xzr, [sp, #40] 0x0000000000400c44 <+20>: str xzr, [sp, #48] 0x0000000000400c48 <+24>: add x0, sp, #0x1b 0x0000000000400c4c <+28>: mov w3, #0x0 // #0 0x0000000000400c50 <+32>: mov x2, #0x1 // #1 0x0000000000400c54 <+36>: mov x1, x0 0x0000000000400c58 <+40>: ldr w0, [sp, #28] 0x0000000000400c5c <+44>: bl 0x405e10 <mq_send> 0x0000000000400c60 <+48>: str w0, [sp, #60] 0x0000000000400c64 <+52>: ldr w0, [sp, #60] 0x0000000000400c68 <+56>: ldp x29, x30, [sp], #64 0x0000000000400c6c <+60>: ret End of assembler dump. (gdb) info b No breakpoints or watchpoints. (gdb) c Continuing. Program received signal SIGILL, Illegal instruction. 0x0000000000400c30 in send () (gdb) x/10x 0x400c30 0x400c30 <send>: 0xd42000a0 0xfd030091 0xe01f00b9 0xe16f0039 0x400c40 <send+16>: 0xff1700f9 0xff1b00f9 0xe06f0091 0x03008052 0x400c50 <send+32>: 0x220080d2 0xe10300aa (gdb) disassemble 0x400c30 Dump of assembler code for function send: => 0x0000000000400c30 <+0>: .inst 0xa00020d4 ; undefined 0x0000000000400c34 <+4>: mov x29, sp 0x0000000000400c38 <+8>: str w0, [sp, #28] 0x0000000000400c3c <+12>: strb w1, [sp, #27] 0x0000000000400c40 <+16>: str xzr, [sp, #40] Signed-off-by: junhua huang <huang.junhua@zte.com.cn> Link: https://lore.kernel.org/r/202212021511106844809@zte.com.cn Signed-off-by: Will Deacon <will@kernel.org> Stable-dep-of: 13f8f1e ("arm64: probes: Fix uprobes for big-endian kernels") Signed-off-by: Sasha Levin <sashal@kernel.org>
chaitu236
pushed a commit
to chaitu236/linux
that referenced
this pull request
Feb 17, 2025
Some of the platforms may connect the INT pin via inversion logic effectively make the triggering to be active-low. Remove explicit trigger flag to respect the settings from firmware. Without this change even idling chip produces spurious interrupts and kernel disables the line in the result: irq 33: nobody cared (try booting with the "irqpoll" option) CPU: 0 UID: 0 PID: 125 Comm: irq/33-i2c-INT3 Not tainted 6.12.0-00236-g8b874ed11dae ni#64 Hardware name: Intel Corp. QUARK/Galileo, BIOS 0x01000900 01/01/2014 ... handlers: [<86e86bea>] irq_default_primary_handler threaded [<d153e44a>] cy8c95x0_irq_handler [pinctrl_cy8c95x0] Disabling IRQ ni#33 Fixes: e6cbbe4 ("pinctrl: Add Cypress cy8c95x0 support") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/20250117142304.596106-2-andriy.shevchenko@linux.intel.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gratian
pushed a commit
that referenced
this pull request
Apr 8, 2025
[ Upstream commit 1ddee69 ] Some of the platforms may connect the INT pin via inversion logic effectively make the triggering to be active-low. Remove explicit trigger flag to respect the settings from firmware. Without this change even idling chip produces spurious interrupts and kernel disables the line in the result: irq 33: nobody cared (try booting with the "irqpoll" option) CPU: 0 UID: 0 PID: 125 Comm: irq/33-i2c-INT3 Not tainted 6.12.0-00236-g8b874ed11dae #64 Hardware name: Intel Corp. QUARK/Galileo, BIOS 0x01000900 01/01/2014 ... handlers: [<86e86bea>] irq_default_primary_handler threaded [<d153e44a>] cy8c95x0_irq_handler [pinctrl_cy8c95x0] Disabling IRQ #33 Fixes: e6cbbe4 ("pinctrl: Add Cypress cy8c95x0 support") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/20250117142304.596106-2-andriy.shevchenko@linux.intel.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
gratian
pushed a commit
that referenced
this pull request
Oct 17, 2025
[ Upstream commit 528eb4e ] When igc_led_setup() fails, igc_probe() fails and triggers kernel panic in free_netdev() since unregister_netdev() is not called. [1] This behavior can be tested using fault-injection framework, especially the failslab feature. [2] Since LED support is not mandatory, treat LED setup failures as non-fatal and continue probe with a warning message, consequently avoiding the kernel panic. [1] kernel BUG at net/core/dev.c:12047! Oops: invalid opcode: 0000 [#1] SMP NOPTI CPU: 0 UID: 0 PID: 937 Comm: repro-igc-led-e Not tainted 6.17.0-rc4-enjuk-tnguy-00865-gc4940196ab02 #64 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:free_netdev+0x278/0x2b0 [...] Call Trace: <TASK> igc_probe+0x370/0x910 local_pci_probe+0x3a/0x80 pci_device_probe+0xd1/0x200 [...] [2] #!/bin/bash -ex FAILSLAB_PATH=/sys/kernel/debug/failslab/ DEVICE=0000:00:05.0 START_ADDR=$(grep " igc_led_setup" /proc/kallsyms \ | awk '{printf("0x%s", $1)}') END_ADDR=$(printf "0x%x" $((START_ADDR + 0x100))) echo $START_ADDR > $FAILSLAB_PATH/require-start echo $END_ADDR > $FAILSLAB_PATH/require-end echo 1 > $FAILSLAB_PATH/times echo 100 > $FAILSLAB_PATH/probability echo N > $FAILSLAB_PATH/ignore-gfp-wait echo $DEVICE > /sys/bus/pci/drivers/igc/bind Fixes: ea57870 ("igc: Add support for LEDs on i225/i226") Signed-off-by: Kohei Enju <enjuk@amazon.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
20 participants
Add this suggestion to a batch that can be applied as a single commit.This suggestion is invalid because no changes were made to the code.Suggestions cannot be applied while the pull request is closed.Suggestions cannot be applied while viewing a subset of changes.Only one suggestion per line can be applied in a batch.Add this suggestion to a batch that can be applied as a single commit.Applying suggestions on deleted lines is not supported.You must change the existing code in this line in order to create a valid suggestion.Outdated suggestions cannot be applied.This suggestion has been applied or marked resolved.Suggestions cannot be applied from pending reviews.Suggestions cannot be applied on multi-line comments.Suggestions cannot be applied while the pull request is queued to merge.Suggestion cannot be applied right now. Please check back later.
This is the 2022Q2.2 stable upgrade for nilrt/master/5.10 from 5.10.109-rt65 to 5.10.115-rt67
There was a minor IRQTF_* enum conflict resolved in place between:
Smoke tests:
Please let me know if I've messed something up. If all goes well and no objections are raised this upgrade will be merged on Tue 5/24.